• 1000 lbs dual thermoplastic melters

$31,000 obo | 956-432-2444 | Valley Striping

• 275 HP High Torque DT-466, only 74,900 miles and 7,628 hours
• an Allison MD-3560 AUTO trans, 14,500 lbs. front axle, 44,000 lbs. rear axles on Hendrickson suspension with a 6.14 gear ratio and A/C.
• Like new 14ft. gravel box mounted to the back with zero rust, previously municipal owned, Texas clean.
• All reconditioned. #4909B

Call for Price | 608-842-3040 | Prairie Truck

• DT466
• Auto
• under CDL
• 168,000 miles

$44,750 | 770-331-2550 | Used Striping Equipment

• 166,215 Miles, Cat Diesel Engine
• Allison Automatic transmission, 165 wheel base,
• 4X2, 9,000 lbs. front axle, 17,500 lbs.
• Read axle 26,500 lbs. GVWR.

$21,000 | 336-792-8265 | Alamance Striping & Equipment

• 62,985 Miles, Spring Type Suspension
• Manual Transmission, 138” Wheel Base
• 4×2, 5,000 lb. Front Axle, 14,200 lb. Rear Axle, 19,200 lb. GVWR
• Engine started and ran

$5000 | 336-792-8265 | Alamance Striping & Equipment

• 127,000 miles on Cummins ISB280 Engine. Allison Transmission. 2 of 1500 lb ASE Falcon Kettles
• Diesel fired Beckett burners. 18ft bed with 12ft available for pallets Venturo 1500lb crane to load
• 3 cyl Kubota aux motor to run paddles. Silent Sentinel 15 lite led arrow board
•  2 of 36” and 2 of 48” underbody boxes for storage of dies etc.

$44,000 | 540-439-8513 | Paynes Design

• PRE-EMISSION 400 HP ISM Cummins engine with low miles and low hours, an Allison HD4560-P
• 6-speed AUTO transmission, 20,000 lbs. front axle and 46,000 lbs. rear axles on Hendrickson suspension, a 5.38 gear ratio, A/C, clean, tight double frame rails with the original black on the 17ft. of frame.
• We have (2) ’07 7600s with 400HP ISM Cummins w/ 4560-P auto trans and ’06 7600 with a 470HP C-13 CAT w/ 4560-P auto trans
• All (3) trucks are Georgia clean and rust free cabs and frame rails. #8594, #8606

Call for Price | 608-842-3040 | Prairie Truck

• Ready to Stripe

$68,750| 770-331-2550 | Used Striping Equipment

• Pre-Emission 435 HP D-12 Engine w/ 132,000 ECM Miles, 6,988 ECM Hours, 6-Speed Allison HD-4560-P, 20K Lbs. Front Axles, 46K Lbs.
• Rear Axles on Hendrickson Air Ride Suspension, Full Lockers, 5.29 Gear Ration, A/C & Power Locks/Windows, Tilt,
• High-Level Wood Grain Interior w/ Bostrom Lumbar Support Seats, Stainless Steel Dump Body. Same Body Style as a 2019 Volvo,
• Included in The Price Of $56,900 is a 4-Way Hydro Turn Plow. #8646

Call for Price | 608-842-3040 | Prairie Truck

• PRE-EGR, ISM Cummins, 350 HP, 145,000 Act. Miles, Low Hours
• HD-4560-P AUTO TRANS, 20,000 lbs, Front Axle, 46,000 lbs. Rear Axles on Hendrickson Leaf
• 5.38 Gear Ratio, Georgia Clean, No Rust, Tight Double Frame
• Hub Piloted Rims, 14’ Box and Hoist, #5085, #5087

Call for Price | 608-842-3040 | Prairie Truck

• PRE-EMISSION 330-350 HP ISM Cummins w/ Low Miles and Low Hours
• Allison HD4650 Automatic Transmission, 14,000 lbs Front Axle, 44,000 lbs Rear Axles on Hendrickson
  Suspension w/ 5.29 Gear Ration On Hub Piloted Rims w/ 95% Matching Tires & A/C.
• This Truck Has a Combo Vac Vermeer Compressor Unit, 850 Model & Vactron System w/ Water Tanks, Etc.
• Will Separate Unit & Sell as Cab Chassis, If So Desired. #8653

Call for Price | 608-842-3040 | Prairie Truck

• Double Drop Bead System
• 160,000 Miles
• Ready to Stripe

$268,500 | 770-331-2550 | Used Striping Equipment

6 Box Grinder Truck

$158,750 | 770-331-2550 | Used Striping Equipment

Dual 1500 lbs. Mini Mac thermoplastic striper

$55,000 OBO | 956-432-2444 | Valley Striping

• Built by Mark Rite Lines #Model 3-410-D s/n 04308
• 220,000 miles on a 7.8 6HK1 Diesel, Allison 3000 Series Transmission
• 4 box set up with 8 drums, 12” with 9.5 width (9” cut path), Saw on front left to cut 101 RPM’s
• Drums are 7 shaft Smith Manufacturing with Smith 12 point cutters

$130,000 | 540-439-8513 | Paynes Design

• Airless Paint Truck with Message Board
• EXCELLENT Condition
• Under 34,000 miles

$175,000 | 770-331-2550 | Used Striping Equipment

PLUNGE CUT SAW TRUCK FOR #101 SNOW PLOWABLE PAVEMENT MARKERS

2018 plunge cut assembly with cutting heads on both sides of truck to cut markers from either side on rebuilt 2011 chassis with under 20k miles since rebuild. 173 hp turbo charged diesel with Plunge Cutting Head with Steel Shroud on each side of truck,vacuum system, diesel power pack, all hydraulics and controls. Includes PCD Blades and Pro Series Diamond Blades. Very Well Maintained and Ready to Work!

$225,000 | 757-857-0734 | American Road Markings

• PRE-EGR, CAT-C7 6 Cylinder, Turbo Charged 300 HP, MD-3560 Auto
• 14,500 lbs Front Axle, 44,000 lbs Rear Axles on Hendrickson FULL LOCKERS
• Brand New Fabco Turbo, A/C, Southern Water + Light
• 14 ft Exhaust Heated Box. 114,000 Miles. #8600

Call for Price | 608-842-3040 | Prairie Truck

• DT 444 E Diesel Engine, 168,000 Miles
• Hydraulic Brakes, Under CDL, 1000 Gallon SealMaster Tank
• 2” ARO Pump, 13HP Air Compressor
• Very clean tool boxes with tons of storage space

$30,000 | 317-800-4062 | SealMaster

• Built by Mark Rite Lines #08117
• 158,901 miles
• 330 gallon paint tanks
• Dual bed tanks

$140,000 | 540-439-8513 | Paynes Design

• 2007 GMC T8500 Paint Truck built by M-B Co Inc.
• Model 1154-5
• 190,027 miles on a 7.8 6HK1
• Allison 3000 series Transmission

$124,000 | 540-439-8513 | Paynes Designs